Harbor Freight Tools Locations

Glad I didn't purchase the 42 when it was on sale or else I would have missed out. submitted by /u/MooreDubs to r/harborfreight [link] [comments]

submitted by /u/Ecstatic-Suspect-306 to r/harborfreight [link] [comments]

submitted by /u/Ecstatic-Suspect-306 to u/Ecstatic-Suspect-306 [link] [comments]

submitted by /u/Ecstatic-Suspect-306 to r/harborfreight [link] [comments]

just got into welding recently, planning on going to trade school for it. nothing too fancy just a flux machine from harbor freight just to practice with. submitted by /u/Ok-Ad6623 to r/Welding [link] [comments]

I made a custom air compressor setup using the tank from a Harbor Freight compressor I bought new in 2016 and two California Air MP100LF pumps. I found out the California Air pumps are actually pretty quiet, and the HF p...

Hello all, I own a 2014 Ram 1500 5.7L with around 174,000 miles. Long story short, this truck was bought as a salvage title a few years back when the mileage was much lower (around 14,000). I have put a new transmission ...

Hello all, I own a 2014 Ram 1500 5.7L with around 174,000 miles. Long story short, this truck was bought as a salvage title a few years back when the mileage was much lower (around 14,000). I have put a new transmission ...

TLDR: If you need a new o-ring for a Briggs and Stratton 500e engine gas cap use part 217 from the Storehouse Metric O-Ring Assortment, 397-Piece o-ring set. A couple months ago I had my gas cap come off my mower with a ...

The Jayport shelf/sink that came with the stock small griddle wasn’t cutting it. Had my Campchef 2 burner from my tenting days. I bought a hitch helper from harbor freight and cut that up to make the 2” square parts. The...

Made this small front rack recently, pretty stoked with how it turned out. 1/4” bent with a $10 harbor freight bender in a vise, welded with fluxcore. submitted by /u/Inevitable_Maybe_855 to r/xbiking [link] [comments]

Is there a place (not necessarily a physical store) like Harbor Freight for bike tools? I am just now getting into riding bikes and I like to learn and maintain my own stuff. I come from 20 years in the car scene and I w...

Is there a place (not necessarily a physical store) like Harbor Freight for bike tools? I am just now getting into riding bikes and I like to learn and maintain my own stuff. I come from 20 years in the car scene and I w...

My job is very light duty. Never gonna need a lot a lot of torque or RPM and I have ready access to my chargers so the tiny batteries are fine. All my M12 stuff, driver, fan, light, mini shop vac, tire inflator, etc all ...

Picked this 2011 up last weekend for a grand. 5 year old batteries and a shot front suspension. Since getting it I replaced the battery cables and did general battery maintenance. PO didn’t know what I was asking about a...

I just completed this wine barrel table, my third project so far. The French oak wine barrel was donated by a winery in Napa Valley. The barrel was pretty heavily used - I sanded to remove as much of the staining/scratch...

Always wanted to learn how to weld and bought myself a welder for my 50th. These are my first 3 attempts ever in order from bottom to top. 1/8" mild steel with Harbor Freight Titanium 125 with settings suggested on the w...

I know my welds are bad. It's a cheap harbor freight welder. I will weigh it down with the concrete blocks in the back. submitted by /u/Manzantee to r/ryobi [link] [comments]

Just picked this tool box up for $50 bucks and needs a few slides replaced. I had no luck finding any on the harbor freight website and was wondering if anyone knows if there are any that will work? Tool box item is Item...

I'm looking to buy an angle grinder, 7" or 9". I'm looking to purchase this in a store and not ordering it online. Only Milwaukee and Hercules offer a 7" to 9" angle grinder. Bauer has a 7" that is a lot cheaper than the...